Hyundai Forums banner
1 - 7 of 7 Posts

·
Registered
Joined
·
17,548 Posts
QUOTE (jsinton @ Aug 8 2010, 02:21 PM) index.php?act=findpost&pid=348001
Four cylinder or six?

Bank 2 will make it a six cylinder... but then we need to know if it a 2.7 or 3.5 :thumbsup:

2.7 --> 39210-37530 Hyundai or Kia dealer should have on shelf for you...

3.5 --> dont have number here at house


Both engines have a few PCM/TCM upgrades available, 1 being Ox swnsor logic for 2.7... come up with engine or edit into you drives vehicle info, I can detail the list of programs for you to update..
 

·
Registered
Joined
·
17,548 Posts
QUOTE (JaxRolo @ Aug 8 2010, 08:48 PM) index.php?act=findpost&pid=348069
I have a 2.7

Is this sensor easy to replace?

Not too hard, it is kinda tight there between radiator and A/C line-Ox sensor body... best done cold so you dont burn hands or fingers..
 

·
Registered
Joined
·
17,548 Posts
Up to '03 was titania, 2004 and later are Zirconia, cannt mix them, the connectors wont fit each other

Go to dealer, have VIN in hand, and parts fella will look it up by VIN, and it will select the correct part... Part number I gave is based off TSB advising to part change for 2004 and up..
 

·
Registered
Joined
·
17,548 Posts
What is the specific code you have ?

There is program for a set of codes depending on what you have for code.
 

·
Registered
Joined
·
17,548 Posts
Repalce the sensor...

TSB covers 0153 and 0133 slow response --> it is a program update..

There is program for intermittent hesitation,, and program for shift feel improvementn I thinjk it is.. plug in GDS, go to ECU UPGRADE< and it'll list what is available if not donee yet based on ROM search.
 

·
Registered
Joined
·
17,548 Posts
I'm having P0150 and P0153 come up as the check engine light comes up. I'm taking my 2006 Tucson 2.7L to the dealer to perform 2 recalls and 1 service campaign. At the same time, I would like them to update the PCM/ECM software so hopefully these codes (and check engine light) go away. Is there a specific software number / revision that I need to ask for? Is this free of charge? Or is it going to cost an arm and a leg? Thanks in advance!

There would be a service charge,, they need to plug in GDS, ID vehicle, enter the ECU UPDATE screen, AUTO Mode, Next, If it pop up Engine as choice, select ENGINE, read ROM,, if anything available to update, it'll pop up in menu below.... always use latest version to be current

Hyundai Motor picks up the (3) recalls,,, you be responsible for the GDS time
 
  • Like
Reactions: [email protected]

·
Registered
Joined
·
17,548 Posts
So, I replaced the sensor, 350 miles later the check engine came back on. It is still giving me the P0150 code. I'm taking the car to the dealer for an ECU update, they will charge $135 for an hour of labor. Hopefully this will clear up the check engine light...I will keep you posted.
2.7L ECM UPDATE - MIL ON WITH DTC P0130/P0150

DESCRIPTION:

This bulletin provides information related to the ECM software update of some 2005-2006MY TUCSON (JM), SANTA FE (SM) or TIBURON (GK) vehicles with 2.7L engines that experience a malfunction indicator lamp illuminated with either of the following ECM (Electronic Control Module) related DTC:

- P0130: O2 Sensor Circuit Malfunction (Bank1/ Sensor 1)
- P0150: O2 Sensor Circuit Malfunction (Bank2/ Sensor 1)

NOTE: This ECM reflash does not require oxygen sensor replacement.

Models: 2005-2006MY TUCSON (JM), SANTA FE (SM), TIBURON (GK) vehicles
with 2.7L engines.

Affected Vehicle Production Date Range: All
 
  • Like
Reactions: [email protected]
1 - 7 of 7 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top