Hyundai Forums banner

1 - 7 of 7 Posts

·
Registered
Joined
·
17,552 Posts
Discussion Starter #1
Good afternoon,, if you own a 2010 Santa Fe, better get on phone or stop into dealer service aisle and make sure all recalls done.. :thumbsup:

I have (2) sitting here with axle splines ground off and rust because the intermediate shaft support did not get modified before the car was sold per Hyundai rules.. axle sit crooked and tore the splines all to #@%*...

I have 2 intermediate shaft with splines worn right off and orange-brown dust.. both are getting axles and transmission.
 

·
Registered
Joined
·
17,552 Posts
Discussion Starter #3
QUOTE (Upthewazzu @ Nov 29 2010, 02:06 PM) index.php?act=findpost&pid=375555
Are these full blown recalls or are they still in "stealth" mode?

Recall, TB8... Not marked "Dealer Only"...


DESCRIPTION:
This bulletin provides a procedure that will prevent or repair an intermediate shaft noise condition on 2010 Santa Fe (CM) vehicles built from October 15, 2009 to March 05, 2010 that have 2.4L engines with automatic transmissions.


VEHICLES AFFECTED:

Model: 2010MY Santa Fe (CM), 2.4L engine with automatic transaxle.

Production Date Range: Oct. 15, 2009 to March 5, 2010.


They 2 I have,, each an open TB8 axle shaft repair, and the TB2 reprogram PCM for the 2.4L on the WEBDCS report.
 

·
SENIOR MODERATOR
Joined
·
9,284 Posts
Whew...I'm in the safe zone. Thanks for letting us know! :thumbsup:
 

·
Registered
Joined
·
17,552 Posts
Discussion Starter #5
QUOTE (lovemysantafe @ Nov 29 2010, 07:09 PM) index.php?act=findpost&pid=375618
Whew...I'm in the safe zone. Thanks for letting us know :thumbsup:

Check your for a TC7 though...

DESCRIPTION:

This bulletin provides information related to an ECM software update to some 2010MY Santa Fe (CM) 3.5L vehicles to revise logic for DTC P0111 Intake Air Temperature Sensor 1 Circuit Range / Performance.

APPLICABLE VEHICLES:

• 2010 Model Year Santa Fe 3.5L
• Production date range: 10/7/2009 ~7/28/2010
 

·
Registered
Joined
·
75 Posts
QUOTE (sbr711 @ Nov 29 2010, 07:19 PM) index.php?act=findpost&pid=375623
Check your for a TC7 though...

DESCRIPTION:

This bulletin provides information related to an ECM software update to some 2010MY Santa Fe (CM) 3.5L vehicles to revise logic for DTC P0111 Intake Air Temperature Sensor 1 Circuit Range / Performance.

APPLICABLE VEHICLES:

• 2010 Model Year Santa Fe 3.5L
• Production date range: 10/7/2009 ~7/28/2010
I've a build date of July 12 2010, and the car is a 3.5 GL, so I'd guess TC7 would need to be applied to my vehicle? It's coming up to 3 months, so I'll be having the first scheduled maintenance, would my dealer (I'm in Canada) perform TC7 as part of that, or would I need to explicitly tell / ask them to do it. I presume there is no cost, as a) it's a recall on their part, and B) I'm covered by warranty for this sort of thing
 

·
Registered
Joined
·
398 Posts
QUOTE (sbr711 @ Nov 29 2010, 04:19 PM) index.php?act=findpost&pid=375623
Check your for a TC7 though...

DESCRIPTION:

This bulletin provides information related to an ECM software update to some 2010MY Santa Fe (CM) 3.5L vehicles to revise logic for DTC P0111 Intake Air Temperature Sensor 1 Circuit Range / Performance.

APPLICABLE VEHICLES:

• 2010 Model Year Santa Fe 3.5L
• Production date range: 10/7/2009 ~7/28/2010

I think they did this one for me when I had the tranny and glovebox looked at. Thanks for the heads up!
 
1 - 7 of 7 Posts
Top