Search Results for ‘clutch’

A few weeks ago when going from 5th to 6th gear there was a dull 'pop' and since then there has been a lot of 'play' in the gear stick and sometimes there is difficulty getting gears to engage. The car is still under warranty but when I called the local dealer a very unhelpful man said they...

Hi, I've had my i20 for just under a year (2nd hand purchase). I have been facing issue that I believe is a clutch problem but hoping to get some guidance. Initially I struggled at times to put the gear into reverse and now on occasion the shift to fourth gear also sometimes won't comply...

I bought my daughter a 2013 Elantra GS Coupe with a manual trans. Clutch question, how far from the floor does the clutch typically start to engage? This car starts to engage quite close to the floor, maybe 2 inches. This car has 90000kms on it.

My Clutch is making this massive grinding noise when engaging to to change gears. Can anyone please suggest what this might be, Clutch slave or the thrush bearing in the clutch??? what parts woulds I need and how much am I looking at? an is it easier than trying to get to the starter...

Evening all, my 2008 2.2d 4x4 santa fe (only bought it a week ago) has suffered a slave cylinder failure, understand it needs a new clutch and flywheel...just trying to find out what clutch kit it needs specifically I.e. is it duel or single mass flywheel etc? Any advice welcome, I want to try...

Hi bought a 2007 diesel yesterday...full history and in near mint condition however i noticed this morning the clutch wasn't coming all the way back up when it was depressed. I didn't notice this on the test drive and Mrs J hasn't noticed either. I'm certain it's the slave cylinder or air in...

Recently purchased a flywheel+clutch kit for my 2013 accent from rockauto. After i finished changing the clutch and reinstalled my transmission the starter wasn't engaging with the flywheel. I discovered that until 7/12/2012 hyundai uses a 106 tooth flywheel, after that they use 127. I ended up...

So just to give context! I purchased my hyundai 2nd hand directly from my local Hyundai Dealership. At the time of purchase it had 19,000 miles on the clock. Its a 2017 Hyundai i20 Turbo Edition. I've had it for around 9 months now and driven 9000 miles. This whole time I've had this slight...

Hi all! I’ve had my little i10 for almost a year now, brought it second hand with 7k miles on the clock (2013 reg), and for the most part I love it. However since owning the car I’ve notice that there doesn’t seem to be any evident biting point on the clutch? I drive it often and it stalls a lot...

Replaced the clutch on a 2005 went smoothly. Shifted exactly twice then the pedal went to the floor. Pulled it back out. And found the retaining clip has come apart allowing the throw out bearing to come out of the pressure plate. WTH? Poor quality parts?

Hey guys, I'm new here as I just bought an 02 Elantra MT with ~115,000 miles about a week ago. Everything was great with the car when I bought it aside from the transmission slipping a little after changing gears. I assumed I would just have to replace the clutch, and it's reasonable to need a...

Hi all, finally got around to posting the how-to on my clutch/slave cylinder replacement I did recently. Filmed it so that you all can do it too if you want to save some dough. Overall was not that bad of a job, didn’t even have to drop the whole transmission! Here’s the link to the edit. Enjoy!

Hi, I've recently changed the clutch in my hyundai i10 1.2 2014, everything went to plan bar my speedometer now failing to function properly. The vss when its original position seems to show a bit of a step where it looks like it could fit into the box so I decided to take the bolt holding it in...

Hello all I've got a 2005 Hyundai Getz 1.6i Manual I've had issues with my clutch slipping and shuddering for a while now, I've had the clutch replaced with release bearing and pressure plate all new. That didn't immediately solve my problem so I took the car back then turned out I had damaged...

Hello all. I have a 2013 i30 and it’s only done 60k miles but it’s a bugger to get in reverse (makes a ‘grunt’ noise when you put it in with the clutch down) and it’s sometimes difficult to get in first or second. Could it be on it’s way out?