 |
 |
|
1 |
darkhack |
287 |
15th March 2008 - 07:05 PM Last post by: darkhack |
[FONT=Arial][SIZE=7][COLOR=blue] Have a 1994 Lantra which still goes very well. Has clocked 116K km. Am thinking of installing enhanced headlight bulbs e.g. xenon car bulbs and enhanced signal/stop/tail lamps in it. Do I need to carry out some modifications to the wiring system or perhaps to instal a conversion kit? default/liebe011.gif'...
 |
|
|
1 |
antonvl |
158 |
11th March 2008 - 02:35 PM Last post by: Otbor 4ere6ka |
I have just bought my 2nd 1993 lantra 1.8 (4g67 engine) but it seems like the balance shafts are not at the right position as there is a lot of vibration when I go over 4500-5000rpm.
I have had a look at the HMA service website but it doesn't say how to set the balance shafts.
Does anyone know how to readjust them?
 |
|
|
0 |
bobojahn |
204 |
6th March 2008 - 05:13 PM Last post by: bobojahn |
Hi everyone,
My step daughter is bringing her Lantra up for my daughter (big sister/little sister thing).
I need to locate a right front window regulator and would like to know where I can source parts online in Australia as we live in Rural NSW.
Also does anyone know where I can get some information on the removal and reinstallation of same.
This will...
 |
|
|
0 |
blatty |
207 |
27th February 2008 - 06:55 AM Last post by: blatty |
Hi guyz. im new to this forum but i would like to know if anyone out there has a workshop manual for a 93 lantra? if they have it electronically maybe i could get it through e-mail. everywhere on the net people asking for money. i am happy to print but there must be a free source somewhere on the net.
any advice?
Cheers
Dan
 |
 |
|
5 |
lantra_span85 |
2,091 |
27th February 2008 - 06:46 AM Last post by: blatty |
Does anybody have the ECU pinout for the HMC39110-33490 model?
It's got three connectors: 26, 16 and 22 pins.
Any help is highly appreciated. default/' '' />
 |
|
|
0 |
Alf76 |
185 |
25th February 2008 - 09:39 AM Last post by: Alf76 |
does anyone experiencing low idle during cold start? sometimes, i need to step on the gas for 1-2 minutes during cold start...what could be the problem?
anyone?
tia..
 |
|
|
1 |
rjpaje |
241 |
12th February 2008 - 11:53 AM Last post by: byronguidry3732 |
i have a 95 elantra and the fuel pump runs with the key off , where is the relay that controls this located . seems like i have unpluged everything under the hood and dash and havent found the right one yet .
 |
|
|
0 |
wsand35 |
114 |
11th February 2008 - 06:56 PM Last post by: wsand35 |
Hi guys, just been on here once, and found enough information to fix cig lighter and replace stereo thank you
 |
|
|
1 |
pcvdriver |
116 |
4th February 2008 - 02:31 PM Last post by: montego |
Check engine and air bag light are on in my 2001 Elantra. In the past when I took to dealership, I was told engine light R/T gas cap not being closed tightly and air bag light on due to something underneath seat. I do not want to pay money for diagnostics for them to tell me everything is R/T what I mentioned earlier. There is not and has not been anything under seat and yes there is possibility...
 |
|
|
1 |
paulaca |
153 |
1st February 2008 - 01:29 PM Last post by: byronguidry3732 |
hi, does any one know where in the USA can buy a pulse generator for a elantra 93 and what part number is?i live in the dominican republic and they dont sell it here thanks
 |
|
|
2 |
romy |
292 |
15th January 2008 - 05:02 PM Last post by: byronguidry3732 |
I have a 2000 Elantra with a bad license lamp and lens. I ordered a part from an online Hyundai parts supplier who required a VIN. The lamp socket I received from them isn't the right one. It's more an oval shape and bigger while the harness plug is smaller and alsmost square. Anyone ever heard of that. I'm about to pull a mickey mouse and use 2 generic connectors on the contacts...
 |
|
|
2 |
ghack |
182 |
2nd January 2008 - 03:25 PM Last post by: ghack |
Hey there, I'm a seasoned DSMer that is in the process of making the ultimate sleeper car. I'm thinking about dropping my race motor into a 1st gen elantra but i need a few answers on some things. From what I hear, 1st gen elantra are easy canidates to do a 4g63t swap. Is there any specific year, engine size that would be more compatible than the other? My guess is that the 1.8L (4g93?)...
 |
|
|
1 |
joshyak |
478 |
27th December 2007 - 05:39 AM Last post by: MDK87 |
Hello To All Worldwide.
Since becoming a Hyundai owner I have studied page after page on Hyundai vehicles & I have come to the conclusion that Hyundai is still a pretty unknown vehicle on the mechanical & electrical side of things.
On many a page I have come across the big question is why does my Hyundai no longer start.
Well the dealership will tell you its a flat battery...
 |
|
|
4 |
LANTRA |
504 |
21st December 2007 - 03:06 PM Last post by: LANTRA |
Hello everybody,
I have a Hyundai Lantra 1.6 of 1992.
My dashboard light is not working.
I have looked at the fuses but they are all right.
But I have only two relays, there should be five.
Are they related to the light?
Or should I check the lights of the dashboard?
Which are for the general dashboard light that turns on when you turn on the headlights?
 |
|
|
1 |
Elfie |
443 |
16th November 2007 - 01:16 PM Last post by: byronguidry3732 |
Hi All, I am new to the forum and I was hoping if someone xould let me know where I can find a wiring diagram for my lantra.
Problem is with the air con switch....I think. default/liebe011.gif' 'liebe011.gif' />
 |
|
|
0 |
bigvmum |
624 |
9th November 2007 - 07:58 AM Last post by: bigvmum |
I am looking to find Clear euro style tail lights for my 1994 Elantra GLS. I have not been very lucky at finding any information in the last year.
Please help.... default/liebe011.gif' 'liebe011.gif' />
Dave
 |
|
|
0 |
jokers_smoke |
292 |
7th November 2007 - 01:10 AM Last post by: jokers_smoke |
Does anybody know approximately where the ignition coil assembly is located on a 93 Elantra (16 DOHC)??????
I'm trying to wire a tachometer myself and am struggling to find it. I have already removed the gauge cluster but it was NOT prewired for a RPM gauge so I have to do it the other way.
offroaders.com/tech/images/autogage2_small.jpg' ...
 |
|
|
1 |
dubtastic89 |
743 |
7th November 2007 - 01:05 AM Last post by: jokers_smoke |
hey i am trying to wire a tach to my car, as my car is EFI i dont know where to attach the green wire that normaly goes on the negitive side of the coil. can some one please help me out.
cheers
 |
|
|
1 |
sutho179 |
393 |
7th November 2007 - 12:47 AM Last post by: jokers_smoke |
Hey, I am having some real trouble finding the wiring diagrams for the 1992 Lantra radio unit.
Am i safe in assuming the Brown wire is constant 12v, black earth, and Dark Green switched 12v?
If thats right, then i'm using the wrong switched 12v wire from my new head unit. As it's not saving the memory.
Also, which is the power antenna wire? Nothing was...
 |
 |
|
1 |
twright901 |
877 |
7th November 2007 - 12:44 AM Last post by: jokers_smoke |
Hey all im having major problems with my car stereo i just removed the old tape deck and i did everything right use the brown as power lime green as Memory and black as ground i forgot to menshion that i have a hyundai lantra 93 model but when i go to power it up it just dosn't want to do it.. odd ive checked fuses etc.. i just can't figure it out... its like the power(brown) isn't...
 |
|
|
2 |
Madogi |
594 |
7th November 2007 - 12:43 AM Last post by: jokers_smoke |
Hi I'm desperately looking for the color wiring for an elantra 94 radio, anyone can help me?
 |
|
|
3 |
pete24 |
1,338 |
7th November 2007 - 12:42 AM Last post by: jokers_smoke |
like the title states, im trying to install a kenwood deck in my 93 elantra but i can't seem to find which wire supplies power, and ground. I assumed the red was power, and black was ground but it didn't work.
can someone please fill me in please?!
 |
|
|
1 |
mkduece |
508 |
7th November 2007 - 12:40 AM Last post by: jokers_smoke |
Hi all! I'm new here and I have a question. I bought a used 1995 Elantra SE and I love it to pieces! I just had to have some work done on it which required removing the battery so that the anti-theft kicked in on the stereo. I have the code for the stereo, however, I punched it in wrong accidentally. How do I reset the thing so that I can re-enter the code the right way? ...
 |
 |
|
2 |
HarmonyStarr |
817 |
7th November 2007 - 12:20 AM Last post by: jokers_smoke |
I posted this before. I need to replace the interior door handle for my son'e 98' Elantra sedan. It lookls like a afew screws and I should be able to tkae it off. Is there anything that is tricky or is irt just removing the screws.
 |
|
|
2 |
steele |
263 |
23rd October 2007 - 01:06 PM Last post by: steele |
I need to replace the interior driver side door handle in my 1998 Elantra. I suspect I need to remove the door to do it. CAn someone give me step by step proceudre to remove the door frame?
 |
|
|
0 |
steele |
194 |
17th October 2007 - 04:46 PM Last post by: steele |
Hello ! default/' '' />
I bought a Hyundai Lantra 1.6GLS and running into a problem so I was hoping there is somebody out here who might be able to help me with it!! Please read on... default/' ...
 |
 |
|
1 |
r.steenis |
761 |
8th August 2007 - 03:22 AM Last post by: r.steenis |
The dashboard light suddenly went dim yesterday.
I had a look at the bulbs but they all seem ok (I am assuming that I looked at the right ones - they were three larger bulbs in the back of the display each covered with a blue plastic cap). All seemed ok and had similar resistances. I suppose it could be that the dimmer switch has broken - it certainly does not alter the light intensity.
 |
 |
|
0 |
IanPowell |
248 |
31st July 2007 - 10:32 PM Last post by: IanPowell |
get lights/radio but clicks @ start, usually indicating bad starter...where is the starter located on 94 elantra?
 |
|
|
0 |
robnatl |
315 |
28th July 2007 - 02:52 PM Last post by: robnatl |
Well i found this forum by accident on yahoo and thoguth i would register.
my car is a 1995 Lantra 1.8 GLS and bought it for $2000 default/biggrin.gif' 'biggrin.gif' /> dont ask why it was so cheap because its hard to explain default/'...
 |
|
|
3 |
CroXtreme |
578 |
3rd July 2007 - 06:28 PM Last post by: CroXtreme |
I am planning of buying a new set of rims online..but I have a problem..I don't know the type of rim installed on my ride..the currently installed rim has a hubcap of mitsubishi so I guess its the same with mitsubishi lancer..all I'm sure is it's a 4 hole rim..heheheh..
Is there a way to find out the type of rim installed in my ride?
is it a pcd 100 or pcd 114?
 |
|
|
9 |
rjpaje |
1,378 |
3rd July 2007 - 04:12 AM Last post by: CroXtreme |
Dear All.
I just found this site. I have not yet looked around, but was hoping anybody could help me.
2 Questions.
What air filter do my car take??? model number, or brief description, is, round with hole in, or sqare block?
and, do it have a fan belt and a timing belt?
1995 Lantra LS 1.5... Bought in UK?
I can give the engine...
 |
|
|
2 |
The Caveman |
268 |
29th June 2007 - 07:15 PM Last post by: The Caveman |
Hi everyone.
We bought a 95 Lantra the other day, 1.8 GLI.
Its done 169,000km.
We have a couple of issues with it and not sure what to do about them.
It seems to rail across bumps and follow the road or deviations in the road, like I will take my hands off the wheel going down our unmade rough driveway and the wheel will so its own thing and follow the...
 |
|
|
3 |
justind |
572 |
27th June 2007 - 10:18 PM Last post by: Madogi |
Well im currently sick of the engine in Lantras and i was wondering whats the best engine i can put in it that has to be under a 2.0l cause of my laws default/sad.gif' 'sad.gif' /> it has to have alot of power cause where i live i aint alowed to drive turbos for another 1.7 years ...
 |
 |
|
2 |
Madogi |
362 |
27th June 2007 - 03:06 AM Last post by: Madogi |
for some odd reason my car has lost alot of its power ive taken it to 3 mechanics and i cant figure it out + it keeps chewing up motor oil like no tomorrow and its not leaking cause theres no oil on the ground in the morning ive even put it in the garage with a white huge sheet of paper i started the car for 10mins turned it off nothing and sometimes its sitting at high revs then it will be gone...
 |
 |
|
5 |
Madogi |
539 |
12th June 2007 - 11:18 PM Last post by: Madogi |
Can I put 1g eclipse knuckles and brakes on my 93' elantra by just bolting them on?? thanks. Ryan from so-cal.
 |
|
|
0 |
hondabait |
298 |
27th May 2007 - 10:00 PM Last post by: hondabait |
I have a 1993 Aust. spec. 18 DOHC Lantra 5 speed with a G4CN motor.
My Question is has anybody tried to put a Mitsubishi 4G93 (or 4G63) DOHC turbo motor in one of these ?
In Australia Front cuts of lancers and Gallants with these motors are readily available and cheaper than getting my Hyundai motor rebuilt and a little bit dearer than getting a low mileage used motor - The 4G93 is...
 |
|
|
4 |
pony-tail |
3,394 |
24th May 2007 - 01:32 AM Last post by: shi shi bog |
i just bought my 93' lantra gl off a mate. it has a fog light button which doesnt appear to work. which lights are meant to work? could someone tell me as i am not sure if its a rear lamp or front lights.
cheers alot
dan
 |
|
|
2 |
lantra_span85 |
436 |
20th May 2007 - 01:44 AM Last post by: Madogi |
default/grin.gif' 'grin.gif' /> Hello, fellow hyundai owners...I'm back..with another problem... default/' '' />
I just noticed that my temp gauge was not...
 |
|
|
3 |
rjpaje |
446 |
19th April 2007 - 07:12 AM Last post by: rjpaje |
my 95 elantra gls 1.8L(manual tranny) idles fine until it warms up. once it warms up it will stall if i dont keep giving it gas. occasionally instead of stalling it goes into a rough idle. was lookin for any insight someone can offer
 |
|
|
1 |
benwizzle |
619 |
15th April 2007 - 06:28 AM Last post by: MDK87 |
[/QUOTE] None of the wrecking yards have a head for my year, make and model .
However I have been told that a head from an eagle talon or an eclipse would fit and work ? If anyone knows what year make an model of car that would work with G4CN ?
 |
 |
|
1 |
notorious1roxybaby |
734 |
15th April 2007 - 06:21 AM Last post by: MDK87 |
I have a 1.6L 1993 Lantra that seems to have developed a serious overheating problem. With obvious things out of the way the usual suspect is the head being cracked but a mate of mine said that they are normally good. So it could be the headgasket. Has anyone had any trouble with there car and if so what was the outcome?
 |
|
|
3 |
costa |
1,006 |
14th April 2007 - 06:40 AM Last post by: notorious1roxybaby |
Can someone please help me. Last month my factory radio finally died. So I went to the local dealership to get a new one. They sold me one that was for a 99 Elantra with a CD player. It was never used, but they couldn't find the book for it. I asked them if it would work in my car and they said it would. So I did the switch. The radio itself works fine, however when I tried the CD...
 |
|
|
0 |
didimays |
494 |
1st April 2007 - 01:43 PM Last post by: didimays |
Hi!
Can anyone help me with this......
I have a 1994 Hyundai Lantra 1.5, and for the last week or so the headlights have been stuck on, even with the switch turned off, and the only way to turn them off is to remove the fuse - it's getting a bit tiresome having to replace the fuse every time I want to drive anywhere at night!!
Can anyone shed some...
 |
|
|
1 |
daveyboy |
292 |
29th March 2007 - 08:57 PM Last post by: Trakka |
|
|